Standard

INVESTIGATION OF FORCE PARAMETERS DURING ROLLING IN RELIEF ROLLS. / Esbolat, Aibol; Panin, Evgeniy A.; Arbuz, A. et al.
In: Journal of Chemical Technology and Metallurgy, Vol. 58, No. 5, 05.2023, p. 961-968.

Research output: Contribution to journal › Article › peer-review

Harvard

Esbolat, A, Panin, EA, Arbuz, A, Kuis, D, Naizabekov, A, Lezhnev, S, Yerzhanov, A, Krupenkin, I, Tolkushkin, A, Kawalek, A & Voroshilov, DS 2023, 'INVESTIGATION OF FORCE PARAMETERS DURING ROLLING IN RELIEF ROLLS', Journal of Chemical Technology and Metallurgy, vol. 58, no. 5, pp. 961-968.

APA

Esbolat, A., Panin, E. A., Arbuz, A., Kuis, D., Naizabekov, A., Lezhnev, S., Yerzhanov, A., Krupenkin, I., Tolkushkin, A., Kawalek, A., & Voroshilov, D. S. (2023). INVESTIGATION OF FORCE PARAMETERS DURING ROLLING IN RELIEF ROLLS. Journal of Chemical Technology and Metallurgy, 58(5), 961-968.

Vancouver

Esbolat A, Panin EA, Arbuz A, Kuis D, Naizabekov A, Lezhnev S et al. INVESTIGATION OF FORCE PARAMETERS DURING ROLLING IN RELIEF ROLLS. Journal of Chemical Technology and Metallurgy. 2023 May;58(5):961-968.

Author

Esbolat, Aibol ; Panin, Evgeniy A. ; Arbuz, A. et al. / INVESTIGATION OF FORCE PARAMETERS DURING ROLLING IN RELIEF ROLLS. In: Journal of Chemical Technology and Metallurgy. 2023 ; Vol. 58, No. 5. pp. 961-968.

BibTeX

@article{d1110f934b174c9cbbe798781d6d7c9a,
title = "INVESTIGATION OF FORCE PARAMETERS DURING ROLLING IN RELIEF ROLLS",
abstract = "The paper presents the results of theoretical studies of the force parameters of thick-sheet blanks rolling in relief rolls. Empirical dependences were obtained to determine the average rolling pressure and force. When studying the pressure, the approach of replacing the deformation scheme with a flat analog was used. In the analysis of the force, the finite element method was used to determine the geometric parameters of the deformation zone. Verification of the obtained dependencies was carried out by comparison with the results of computer simulation. Comparative analysis showed high convergence of the calculation and simulation results, as well as the possibility of applying the formulas obtained not only for symmetrical rolling or for speed asymmetry, but also in the case of rolling in relief rolls of different diameters. {\textcopyright} 2023, Journal of Chemical Technology and Metallurgy. All Rights Reserved.",
author = "Aibol Esbolat and Panin, {Evgeniy A.} and A. Arbuz and Dmitry Kuis and Abdrakhman Naizabekov and S. Lezhnev and Almas Yerzhanov and Ivan Krupenkin and A. Tolkushkin and Anna Kawalek and Voroshilov, {Denis S.}",
note = "This research was funded by the Science Committee of the Ministry of Education and Science of the Republic of Kazakhstan (Grant № AP14869080).",
year = "2023",
month = may,
language = "English",
volume = "58",
pages = "961--968",
journal = "Journal of Chemical Technology and Metallurgy",
issn = "1314-7471",
publisher = "University of Chemical Technology and Metallurgy",
number = "5",

}

RIS

TY - JOUR

T1 - INVESTIGATION OF FORCE PARAMETERS DURING ROLLING IN RELIEF ROLLS

AU - Esbolat, Aibol

AU - Panin, Evgeniy A.

AU - Arbuz, A.

AU - Kuis, Dmitry

AU - Naizabekov, Abdrakhman

AU - Lezhnev, S.

AU - Yerzhanov, Almas

AU - Krupenkin, Ivan

AU - Tolkushkin, A.

AU - Kawalek, Anna

AU - Voroshilov, Denis S.

N1 - This research was funded by the Science Committee of the Ministry of Education and Science of the Republic of Kazakhstan (Grant № AP14869080).

PY - 2023/5

Y1 - 2023/5

N2 - The paper presents the results of theoretical studies of the force parameters of thick-sheet blanks rolling in relief rolls. Empirical dependences were obtained to determine the average rolling pressure and force. When studying the pressure, the approach of replacing the deformation scheme with a flat analog was used. In the analysis of the force, the finite element method was used to determine the geometric parameters of the deformation zone. Verification of the obtained dependencies was carried out by comparison with the results of computer simulation. Comparative analysis showed high convergence of the calculation and simulation results, as well as the possibility of applying the formulas obtained not only for symmetrical rolling or for speed asymmetry, but also in the case of rolling in relief rolls of different diameters. © 2023, Journal of Chemical Technology and Metallurgy. All Rights Reserved.

AB - The paper presents the results of theoretical studies of the force parameters of thick-sheet blanks rolling in relief rolls. Empirical dependences were obtained to determine the average rolling pressure and force. When studying the pressure, the approach of replacing the deformation scheme with a flat analog was used. In the analysis of the force, the finite element method was used to determine the geometric parameters of the deformation zone. Verification of the obtained dependencies was carried out by comparison with the results of computer simulation. Comparative analysis showed high convergence of the calculation and simulation results, as well as the possibility of applying the formulas obtained not only for symmetrical rolling or for speed asymmetry, but also in the case of rolling in relief rolls of different diameters. © 2023, Journal of Chemical Technology and Metallurgy. All Rights Reserved.

UR - http://www.scopus.com/inward/record.url?partnerID=8YFLogxK&scp=85164586057

M3 - Article

VL - 58

SP - 961

EP - 968

JO - Journal of Chemical Technology and Metallurgy

JF - Journal of Chemical Technology and Metallurgy

SN - 1314-7471

IS - 5

ER -

ID: 41996591