Результаты исследований: Вклад в журнал › Статья › Рецензирование
Результаты исследований: Вклад в журнал › Статья › Рецензирование
}
TY - JOUR
T1 - Effect of moderate plastic deformation on structure and properties of the ordered Cu–56Au (at.%) alloy
AU - Volkov, Alexey Yu.
AU - Antonova, Olga V.
AU - Komkova, Daria A.
AU - Glukhov, Andrey V.
AU - Volkova, Elena G.
AU - Livinets, Alyona A.
AU - Podgorbunskaya, Polina O.
AU - Antonov, Boris D.
N1 - The research was supported by Grant No. 21-13-00135 of the Russian Science Foundation.
PY - 2023
Y1 - 2023
N2 - The effect of plastic deformation on the structure and properties of the ordered Cu–56Au (at.%) alloy has been studied. The deformation strain has been expressed in the cross-section area reduction (CSAR) percent from 10 to 80%. The dependences of electrical resistivity and microhardness on CSAR of both ordered and disordered alloy specimens have been plotted. Mechanical tensile tests of specimens in various structural states have also been carried out. It has been shown that after plastic deformation, the microhardness of the pre-ordered Cu–56Au alloy increases significantly and becomes higher than the microhardness of the severely deformed initially disordered alloy. It has been established that the deformation up to 70% CSAR does not cause a complete destruction of the atomic order. It has been shown that moderate plastic deformation (at 10–30% CSAR) of the ordered Cu–56Au alloy leads to obtaining of a thermal stability material exhibiting an excellent balance between high strength and low electrical resistivity. Such behavior of the alloy is attributed to the occurrence of an enriched dislocation density in the deformed ordered structure in which the deformation-induced disordered phase has not begun to form yet. © 2023 Elsevier B.V.
AB - The effect of plastic deformation on the structure and properties of the ordered Cu–56Au (at.%) alloy has been studied. The deformation strain has been expressed in the cross-section area reduction (CSAR) percent from 10 to 80%. The dependences of electrical resistivity and microhardness on CSAR of both ordered and disordered alloy specimens have been plotted. Mechanical tensile tests of specimens in various structural states have also been carried out. It has been shown that after plastic deformation, the microhardness of the pre-ordered Cu–56Au alloy increases significantly and becomes higher than the microhardness of the severely deformed initially disordered alloy. It has been established that the deformation up to 70% CSAR does not cause a complete destruction of the atomic order. It has been shown that moderate plastic deformation (at 10–30% CSAR) of the ordered Cu–56Au alloy leads to obtaining of a thermal stability material exhibiting an excellent balance between high strength and low electrical resistivity. Such behavior of the alloy is attributed to the occurrence of an enriched dislocation density in the deformed ordered structure in which the deformation-induced disordered phase has not begun to form yet. © 2023 Elsevier B.V.
UR - http://www.scopus.com/inward/record.url?partnerID=8YFLogxK&scp=85149791393
UR - https://gateway.webofknowledge.com/gateway/Gateway.cgi?GWVersion=2&SrcAuth=tsmetrics&SrcApp=tsm_test&DestApp=WOS_CPL&DestLinkType=FullRecord&KeyUT=000976133800001
U2 - 10.1016/j.msea.2023.144626
DO - 10.1016/j.msea.2023.144626
M3 - Article
VL - 865
JO - Materials science and engineering a-Structural materials properties microstructure and processing
JF - Materials science and engineering a-Structural materials properties microstructure and processing
SN - 0921-5093
M1 - 144626
ER -
ID: 36196447