Standard

One-Step Non-Contact Additive LIFT Printing of Silver Interconnectors for Flexible Printed Circuits. / Nastulyavichus, Alena; Kudryashov, Sergey; Shelygina, Svetlana et al.
In: Photonics, Vol. 11, No. 2, 119, 2024.

Research output: Contribution to journal › Article › peer-review

Harvard

Nastulyavichus, A, Kudryashov, S, Shelygina, S, Smirnov, N, Pakholchuk, P, Saraeva, I, Zayarny, D, Ulturgasheva, E, Khmelenin, D, Emelyanova, O, Pryakhina, V, Pokryshkin, N, Kuzmin, E, Gorevoy, A, Minh, P & Van Duong, P 2024, 'One-Step Non-Contact Additive LIFT Printing of Silver Interconnectors for Flexible Printed Circuits', Photonics, vol. 11, no. 2, 119. https://doi.org/10.3390/photonics11020119

APA

Nastulyavichus, A., Kudryashov, S., Shelygina, S., Smirnov, N., Pakholchuk, P., Saraeva, I., Zayarny, D., Ulturgasheva, E., Khmelenin, D., Emelyanova, O., Pryakhina, V., Pokryshkin, N., Kuzmin, E., Gorevoy, A., Minh, P., & Van Duong, P. (2024). One-Step Non-Contact Additive LIFT Printing of Silver Interconnectors for Flexible Printed Circuits. Photonics, 11(2), [119]. https://doi.org/10.3390/photonics11020119

Vancouver

Nastulyavichus A, Kudryashov S, Shelygina S, Smirnov N, Pakholchuk P, Saraeva I et al. One-Step Non-Contact Additive LIFT Printing of Silver Interconnectors for Flexible Printed Circuits. Photonics. 2024;11(2):119. doi: 10.3390/photonics11020119

Author

Nastulyavichus, Alena ; Kudryashov, Sergey ; Shelygina, Svetlana et al. / One-Step Non-Contact Additive LIFT Printing of Silver Interconnectors for Flexible Printed Circuits. In: Photonics. 2024 ; Vol. 11, No. 2.

BibTeX

@article{a844c3e9950d4e55ade664ead4bce197,
title = "One-Step Non-Contact Additive LIFT Printing of Silver Interconnectors for Flexible Printed Circuits",
abstract = "The single-pass one-step method for printing conductive silver tracks on a glass surface, using the laser-induced forward transfer (LIFT) technique, was proposed, providing a unique opportunity for high-throughput printing of surface micro- and nanostructures with high electrical conductivity and positioning accuracy. This method was developed via our multi-parametric research, resulting in the selection of the optimal material, laser irradiation, and transfer conditions. Optical, scanning and transmission electron, and atomic force microscopy methods, as well as X-ray diffraction, were used to characterize the surface structure and phase state of the printed structures, while energy-dispersive X-ray and X-ray photoelectron microscopy were employed for their chemical microanalysis. Depending on the laser irradiation parameters, the specific electrical conductivity of the printed tracks varied from 0.18 to 83 kS/cm, approaching that of donor magnetron-sputtered films. This single-pass one-step method significantly facilitates fast, large-scale, on-demand local laser printing of metallic (sub)microcomponents of microelectronic devices. {\textcopyright} 2024 by the authors.",
author = "Alena Nastulyavichus and Sergey Kudryashov and Svetlana Shelygina and Nikita Smirnov and Petr Pakholchuk and Irina Saraeva and Dmitry Zayarny and Evgenia Ulturgasheva and Dmitry Khmelenin and Olga Emelyanova and Victoria Pryakhina and Nikolay Pokryshkin and Evgeny Kuzmin and Alexey Gorevoy and Pham Minh and {Van Duong}, Pham",
note = "Текст о финансировании #1 This research was supported by the Ministry of Science and Higher Education of the Russian Federation (agreement no. 075-15-2023-603). Текст о финансировании #2 The equipment used was supplied by the Ural Center for Shared Use “Modern Nanotechnology” of Ural Federal University (Reg. no. 2968), which is supported by the Ministry of Science and Higher Education RF and of the Center for Collective Use “Structural Diagnostics of Materials” of the Federal Scientific Research Center “Crystallography and Photonics” of the Russian Academy of Sciences.",
year = "2024",
doi = "10.3390/photonics11020119",
language = "English",
volume = "11",
journal = "Photonics",
issn = "2304-6732",
publisher = "Multidisciplinary Digital Publishing Institute (MDPI)",
number = "2",

}

RIS

TY - JOUR

T1 - One-Step Non-Contact Additive LIFT Printing of Silver Interconnectors for Flexible Printed Circuits

AU - Nastulyavichus, Alena

AU - Kudryashov, Sergey

AU - Shelygina, Svetlana

AU - Smirnov, Nikita

AU - Pakholchuk, Petr

AU - Saraeva, Irina

AU - Zayarny, Dmitry

AU - Ulturgasheva, Evgenia

AU - Khmelenin, Dmitry

AU - Emelyanova, Olga

AU - Pryakhina, Victoria

AU - Pokryshkin, Nikolay

AU - Kuzmin, Evgeny

AU - Gorevoy, Alexey

AU - Minh, Pham

AU - Van Duong, Pham

N1 - Текст о финансировании #1 This research was supported by the Ministry of Science and Higher Education of the Russian Federation (agreement no. 075-15-2023-603). Текст о финансировании #2 The equipment used was supplied by the Ural Center for Shared Use “Modern Nanotechnology” of Ural Federal University (Reg. no. 2968), which is supported by the Ministry of Science and Higher Education RF and of the Center for Collective Use “Structural Diagnostics of Materials” of the Federal Scientific Research Center “Crystallography and Photonics” of the Russian Academy of Sciences.

PY - 2024

Y1 - 2024

N2 - The single-pass one-step method for printing conductive silver tracks on a glass surface, using the laser-induced forward transfer (LIFT) technique, was proposed, providing a unique opportunity for high-throughput printing of surface micro- and nanostructures with high electrical conductivity and positioning accuracy. This method was developed via our multi-parametric research, resulting in the selection of the optimal material, laser irradiation, and transfer conditions. Optical, scanning and transmission electron, and atomic force microscopy methods, as well as X-ray diffraction, were used to characterize the surface structure and phase state of the printed structures, while energy-dispersive X-ray and X-ray photoelectron microscopy were employed for their chemical microanalysis. Depending on the laser irradiation parameters, the specific electrical conductivity of the printed tracks varied from 0.18 to 83 kS/cm, approaching that of donor magnetron-sputtered films. This single-pass one-step method significantly facilitates fast, large-scale, on-demand local laser printing of metallic (sub)microcomponents of microelectronic devices. © 2024 by the authors.

AB - The single-pass one-step method for printing conductive silver tracks on a glass surface, using the laser-induced forward transfer (LIFT) technique, was proposed, providing a unique opportunity for high-throughput printing of surface micro- and nanostructures with high electrical conductivity and positioning accuracy. This method was developed via our multi-parametric research, resulting in the selection of the optimal material, laser irradiation, and transfer conditions. Optical, scanning and transmission electron, and atomic force microscopy methods, as well as X-ray diffraction, were used to characterize the surface structure and phase state of the printed structures, while energy-dispersive X-ray and X-ray photoelectron microscopy were employed for their chemical microanalysis. Depending on the laser irradiation parameters, the specific electrical conductivity of the printed tracks varied from 0.18 to 83 kS/cm, approaching that of donor magnetron-sputtered films. This single-pass one-step method significantly facilitates fast, large-scale, on-demand local laser printing of metallic (sub)microcomponents of microelectronic devices. © 2024 by the authors.

UR - http://www.scopus.com/inward/record.url?partnerID=8YFLogxK&scp=85187311770

UR - https://gateway.webofknowledge.com/gateway/Gateway.cgi?GWVersion=2&SrcAuth=tsmetrics&SrcApp=tsm_test&DestApp=WOS_CPL&DestLinkType=FullRecord&KeyUT=001172404300001

U2 - 10.3390/photonics11020119

DO - 10.3390/photonics11020119

M3 - Article

VL - 11

JO - Photonics

JF - Photonics

SN - 2304-6732

IS - 2

M1 - 119

ER -

ID: 54326051